
ADuM3210/ADuM3211
Data Sheet
ELECTRICAL CHARACTERISTICS—5 V, 125°C OPERATION
All typical specifications are at T A = 25°C, V DD1 = V DD2 = 5 V. Minimum/maximum specifications apply over the entire recommended
operation range: 4.5 V ≤ V DD1 ≤ 5.5 V, 4.5 V ≤ V DD2 ≤ 5.5 V, and ?40°C ≤ T A ≤ +125°C, unless otherwise noted. Switching specifications
are tested with C L = 15 pF and CMOS signal levels, unless otherwise noted.
Table 13.
WA Grade
WB Grade, T Grade
WC Grade
Test Conditions/
Parameter
Symbol
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Unit
Comments
SWITCHING SPECIFICATIONS
Data Rate
1
10
25
Mbps
Within PWD limit
Propagation Delay
t PHL , t PLH
20
50
20
50
20
50
ns
50% input to 50%
output
Pulse Width Distortion
Change vs. Temperature
Pulse Width
Propagation Delay Skew
PWD
PW
t PSK
1000
6
5
20
100
5
3
18
40
5
3
18
ns
ps/°C
ns
ns
|t PLH ? t PHL |
Within PWD limit
Between any two units
Channel Matching
Codirectional
Opposing Directional
t PSKCD
t PSKOD
5
20
3
18
3
18
ns
ns
Output Rise/Fall Time
t R /t F
2.5
2.5
2.5
ns
10% to 90%
Table 14.
1 Mbps—WA Grade,
WB Grade, WC Grade,
T Grade
10 Mbps—WB Grade,
WC Grade
10 Mbps—T Grade
25 Mbps—WC Grade
Parameter
Symbol
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Unit
SUPPLY CURRENT
ADuM3210
ADuM3211
I DD1
I DD2
I DD1
I DD2
1.3
1.0
1.1
1.3
1.7
1.6
1.5
1.8
3.5
1.7
2.6
3.1
4.6
2.8
3.4
4.0
3.5
2.0
3.0
3.1
4.8
2.8
4.0
4.1
6.6
3.7
5.3
5.9
9.0
4.5
7.5
8.0
mA
mA
mA
mA
Table 15. For All Models
Parameter
Symbol
Min
Typ
Max
Unit
Test Conditions/Comments
DC SPECIFICATIONS
Logic High Input Threshold
Logic Low Input Threshold
V IH
V IL
0.7 V DDx
0.3 V DDx
V
V
Logic High Output Voltages
V OH
V DDx ? 0.1
V DDx ? 0.5
5.0
4.8
V
V
I Ox = ?20 μA, V Ix = V IxH
I Ox = ?4 mA, V Ix = V IxH
Logic Low Output Voltages
V OL
0.0
0.2
0.1
0.4
V
V
I Ox = 20 μA, V Ix = V IxL
I Ox = 4 mA, V Ix = V IxL
Input Current per Channel
I I
?10
+0.01
+10
μA
0 V ≤ V Ix ≤ V DDx
Supply Current per Channel
Quiescent Input Supply Current
Quiescent Output Supply Current
Dynamic Input Supply Current
Dynamic Output Supply Current
I DDI(Q)
I DDO(Q)
I DDI(D)
I DDO(D)
0.4
0.4
0.19
0.05
0.8
0.8
mA
mA
mA/Mbps
mA/Mbps
AC SPECIFICATIONS
Common-Mode Transient Immunity 1
Refresh Rate
|CM|
f r
25
35
1.2
kV/μs
Mbps
V Ix = V DDx , V CM = 1000 V,
transient magnitude = 800 V
1
|CM| is the maximum common-mode voltage slew rate that can be sustained while maintaining V O > 0.8 V DD . The common-mode voltage slew rates apply to both
rising and falling common-mode voltage edges.
Rev. I | Page 8 of 24